Custom PBT filament is where a broom stops looking like every other broom on the shelf. The same polymer can be drawn fine or coarse, dyed to a brand colour, crimped for volume or flagged for dust pickup, and each choice changes how the finished broom sweeps and sells. This guide walks through the four main options, how they interact, and what to ask a PBT broom filaments manufacturer before placing a custom order.
Custom PBT broom filament is defined by four choices: diameter, usually 0.15 to 0.8 mm; colour, matched in the melt to a Pantone or RAL reference; crimp, set by wave pitch and height; and tip, either plain, tapered or flagged. A capable producer lets you set all four independently and confirms them in an approved sample.
Why Do Buyers Choose PBT Over PET and PP for Broom Filaments?
PBT earns its higher price through bend recovery, the ability of a filament to spring back to straight after being pressed flat. A broom head is pushed against a floor thousands of times, and a filament that recovers keeps its sweeping edge while one that stays bent leaves the head looking tired within weeks.
The physical numbers back this up. PBT has a density of about 1.30 g/cm³ against 1.38 for PET and 0.91 for PP, and it melts near 225°C. It also absorbs far less moisture than nylon, so a PBT broom keeps its shape in a damp utility room or a wet kitchen.
PBT has limits, and a good manufacturer will say so. Prolonged contact with hot, strongly alkaline cleaners can break the polymer down through hydrolysis, so PP is often the safer pick for steam-cleaned or caustic washdown areas.
Cost is the other trade-off. PBT resin generally costs more than PET or PP, which is why buyers reserve it for premium household brooms, fine-sweep brooms and brushes where appearance after months of use sells the product.
Diameter and Colour: The First Two Choices to Set
How Thick Should PBT Broom Filament Be?
Diameter sets stiffness, and stiffness rises with the fourth power of thickness. Most custom orders fall between 0.15- and 0.8-mm. Grades of 0.15 to 0.30 mm suit soft indoor brooms, 0.30 to 0.50 mm covers all-purpose household brooms, and 0.50 mm and above handles patio and outdoor work.
Tolerance belongs in writing. A figure of ±0.02 mm is a fair request for filament under 0.5 mm, and a producer who can hold it is controlling the extrusion line itself, not just the paperwork.
How Is Colour Matched in PBT Filament?
Colour added through masterbatch in the melt runs through the whole strand. It does not rub off or wash out, and tips that wear down keep their shade, which matters for brooms sold on appearance.
Send a Pantone or RAL reference, plus a physical swatch if the colour is critical, and agree a Delta E tolerance with the supplier. A range of 1.0 to 1.5 is a common starting point. Custom colours often carry a minimum order of a few hundred kilograms, so test a shade on a small run first.
Batch-to-batch consistency is where a PBT broom filaments manufacturer earns trust. Ask for a retained sample from each batch, so a later shipment can be compared against the original under the same light.
How Do Crimp and Flagged Tips Change the Way a Broom Sweeps?
Crimp controls volume and flagged tips control pickup, and the two work on different parts of the filament. Crimp is the wave set along the strand, defined by pitch, the distance between peaks, and amplitude, the height of each wave. Tighter pitch and deeper amplitude pack more bulk into the head, so fewer filaments make a fuller broom.
Straight filament still has a place. An uncrimped fill sweeps with a cleaner, firmer line on hard floors, which is why many fine-sweep brooms use it. Crimp suits brooms that need coverage on uneven ground.
Crimp needs heat setting to last. PBT’s elasticity helps it hold a wave well, but ask the producer how the crimp is set and whether it survives a hot-water soak test.
A flagged tip splits the end of each filament into several fine fibres. Those fibres have far more surface area than a plain cut end, so they hold fine dust, hair and pet fur instead of pushing it across the floor. Plain tips cannot match that pickup at any diameter.
Tip options run from plain through tapered to fully flagged. Tapering narrows the final few millimetres for a softer edge, and tapering plus flagging gives the softest result. Cost rises with each processing step, so match the tip to the surface the broom will sweep.
How Do the Four Options Work Together?
Most successful custom specs combine all four options rather than maximising one. The table shows three starting points that buyers commonly adapt.
| Broom type | Diameter (mm) | Colour | Crimp | Tip |
| Soft indoor broom | 0.20–0.30 | Light or pastel | Fine | Flagged |
| All-purpose household | 0.30–0.45 | Brand colour | Medium | Tapered, flagged |
| Outdoor push broom | 0.50–0.80 | Dark | Deep | Plain or tapered |
Mixed fills are worth considering. A producer like Santone should be able to quote two diameters in one order, giving the head a firmer backbone and a finer flagged top layer for dust.
Cut length belongs in the spec too. In folded tufting, cut length is roughly twice the trim length plus the anchor allowance, so a 110 mm trim needs about 235 to 250 mm of filament. Confirm the exact figure against your own machine.
Price follows the choices. Fine diameters, deep crimps and flagging each add processing time, so a quote for 0.25 mm flagged filament will sit well above one for plain 0.5 mm. Ask for the cost of each option separately to see which one is worth paying for.
What to Ask a PBT Broom Filaments Manufacturer Before You Order
A sample, not a catalogue, is the first thing a serious manufacturer should offer. Request two to five kilograms made to your spec, measure diameter at five points on ten filaments with a micrometer, and compare colour to your reference under daylight and shop light.
Production capability matters as much as the sample. Ask how many extrusion lines run PBT, whether crimping and flagging happen in-house, and what the monthly output is in tonnes. Many listings for a PBT broom filaments supplier belong to traders who subcontract these steps, which slows every custom change.
Export handling deserves its own questions. A reliable PBT broom filaments exporter prepares the commercial invoice, packing list and certificate of origin, states the customs classification, and packs filament straight in moisture-barrier cartons marked with batch numbers. Sea freight from China typically adds 20 to 40 days, so plan reorders about ten weeks ahead.
Paperwork should include batch reports covering diameter variation, tensile strength and bend recovery, and buyers shipping into Europe should request a REACH statement for the polymer and colourants. A supplier such as Santone should be able to provide these on request, and hesitation is a warning sign.
Frequently Asked Questions
Is PBT better than PET for broom filament?
PBT recovers from bending better and keeps its shape longer, which suits premium brooms. PET costs less and is stiffer, so it remains the usual pick for budget and outdoor brooms.
What diameters are available for custom PBT broom filament?
Most producers offer 0.15 to 0.8 mm, with thicker grades available on request. Fine grades suit soft indoor brooms, and the upper range suits outdoor work.
Can PBT broom filament be made in custom colours?
Yes. Colour is added in the melt from a Pantone or RAL reference, and custom shades often need a minimum order of a few hundred kilograms.
What is a flagged tip on a broom filament?
A flagged tip is an end split into several fine fibres. The extra surface area catches fine dust and hair that a plain tip would push along.
How long does a custom PBT filament order take?
Production commonly takes 15 to 30 days once the sample is approved. Sea freight adds roughly 20 to 40 days depending on the destination port.
Draft a one-page brief with all four choices set out: diameter and tolerance, Pantone or RAL colour, crimp pitch and amplitude, and tip type, plus the cut length your tufting machine needs. Send the identical brief to two or three producers, and the quality of the questions that come back will show who understands the work.
Then run the samples through your own machine and a real sweep trial before ordering in bulk. The right PBT broom filaments manufacturer will treat that trial as the start of a working relationship and adjust one variable at a time, whether you share the results with Santone or any other shortlisted producer.